Qantas A388 at Los Angeles on Jan 1st 2024, maintenance tool found left in engine
Last Update: November 14, 2024 / 12:01:38 GMT/Zulu time
Incident Facts
Date of incident
Jan 1, 2024
Classification
Report
Airline
Qantas
Flight number
QF-11
Departure
Sydney, Australia
Destination
Los Angeles, United States
Aircraft Registration
VH-OQI
Aircraft Type
Airbus A380-800
ICAO Type Designator
A388
The aircraft subsequently went into maintenance, where it was discovered a tool had been left in the left hand engine (Trent 972) during previous maintenance between Dec 6th and 9th 2023. The tool had been missing since.
On Nov 14th 2024 the ATSB released their final report concluding the causes of the incident were:
Contributing factors
- An aircraft maintenance engineer and a licenced maintenance engineer did not observe an engine turning tool that was left in the low-pressure compressor case during their foreign object inspections after maintenance on the engine.
- The lost tool procedure was not commenced by the involved aircraft maintenance engineers when the tool was identified as missing.
- The service engineer certified a certificate of release (CRS) with the tool unaccounted for. As a result, the aircraft flew 34 cycles and 293.74 hours with the turning tool in the outboard left engine low-pressure compressor.
The ATSB summarized the sequence of events:
On 6 December 2023, an Airbus A380-842 aircraft, registered VH-OQI and operated by Qantas Airways Limited, was undergoing a 3-day scheduled maintenance check at Los Angeles International Airport (LAX), United States.
On day one of the maintenance check, during a scheduled borescope inspection of the outboard left engine, a tool was left in the engine inlet. On the evening of 8 December, the aircraft was released to service and departed for Melbourne, Victoria.
On 1 January 2024, the aircraft returned to the LAX maintenance facility for a 3-day scheduled maintenance check, where the missing tool was discovered in the outboard left engine low-pressure compressor. The aircraft had flown 34 cycles totalling 293.74 hours with the tool in the outboard left engine.
The ATSB found that the tool was not located during the end of task foreign object inspections, which resulted in it remaining in the engine. The Qantas Engineering lost tool procedure was not commenced prior to the aircraft being released to service and the certifying engineer did not follow up on the lost tool, prior to releasing the aircraft to service.
The ATSB released following safety message:
Foreign object debris and damage poses a significant threat to the safe operation of aircraft. Regulations, procedures, and training have been put in place and refined to limit the risk of foreign object damage, especially from introduced objects during maintenance. As a result, the correct application of tool control is an important, fundamental, and necessary aspect of the maintenance process to mitigate any human errors that may arise.
Incident Facts
Date of incident
Jan 1, 2024
Classification
Report
Airline
Qantas
Flight number
QF-11
Departure
Sydney, Australia
Destination
Los Angeles, United States
Aircraft Registration
VH-OQI
Aircraft Type
Airbus A380-800
ICAO Type Designator
A388
This article is published under license from Avherald.com. © of text by Avherald.com.
Article source
You can read 2 more free articles without a subscription.
Subscribe now and continue reading without any limits!
Read unlimited articles and receive our daily update briefing. Gain better insights into what is happening in commercial aviation safety.
Send tip
Support AeroInside by sending a small tip amount.
Related articles
Qantas A388 over Slovakia on Jul 14th 2023, technical problem, overweight landing with max reverse needed in London
A Qantas Airbus A380-800, registration VH-OQI performing flight QF-2 from London Heathrow,EN (UK) to Singapore (Singapore), was enroute at FL330 just…
Qantas A388 over Germany on Jul 14th 2023, autopilot failure
A Qantas Airbus A380-800, registration VH-OQI performing flight QF-1 (dep Jul 13th) from Singapore (Singapore) to London Heathrow,EN (UK), was…
Qantas A388 near Sydney on Aug 3rd 2016, cabin temperature regulation fault
A Qantas Airbus A380-800, registration VH-OQI performing flight QF-1 from Sydney,NS (Australia) to Dubai (United Arab Emirates), was climbing through…
Qantas A388 near Melbourne on Jun 2nd 2015, cabin did not properly pressurize
A Qantas Airbus A380-800, registration VH-OQI performing flight QF-93 from Melbourne,VI (Australia) to Los Angeles,CA (USA), was climbing out of…
Qantas B738 at Sydney on Nov 8th 2024, engine failure on departure sets grass alight
A Qantas Boeing 737-800, registration VH-VYH performing flight QF-520 from Sydney,NS to Brisbane,QL (Australia) with 181 people and dry ice on board,…
Qantas B738 over Tasman Sea on Oct 2nd 2024, odour on board
A Qantas Boeing 737-800, registration VH-XZL performing flight QF-163 from Sydney,NS (Australia) to Wellington (New Zealand) with 144 people on…
Qantas A332 at Perth on Sep 15th 2024, blew up runway surface on departure
A Qantas Airbus A330-200, registration VH-EBD performing flight QF-71 from Perth,WA (Australia) to Singapore (Singapore), was in the initial…
Qantas B789 at Rome and Perth on Aug 24th 2024, tyre damage on departure
A Qantas Boeing 787-9, registration VH-ZNC performing flight QF-6 (dep Aug 23rd) from Rome Fiumicino (Italy) to Perth,WA (Australia), landed on…
Qantaslink E190 near Townsville on Jul 27th 2024, loss of cabin pressure
A Qantaslink Embraer ERJ-190, registration VH-XVP performing flight QF-1871 from Townsville,QL to Brisbane,QL (Australia) with 87 people on board,…
Newest articles
Spring Japan A321 at Sapporo on Nov 29th 2024, runway incursion by vehicle
A Spring Airlines Japan Airbus A321-200 freighter, registration JA82YA performing flight IJ-407 (dep Nov 28th) from Tokyo Narita to Sapporo New…
Commut E145 near Monroe on Dec 2nd 2024, smoke in cockpit
A CommutAir Embraer ERJ-145 on behalf of United, registration N14148 performing flight UA-4830 from Little Rock,AR to Houston Intercontinental,TX…
Subscribe today
Are you researching aviation incidents? Get access to AeroInside Insights, unlimited read access and receive the daily newsletter.
Pick your plan and subscribePartner
A new way to document and demonstrate airworthiness compliance and aircraft value. Find out more.
ELITE Simulation Solutions is a leading global provider of Flight Simulation Training Devices, IFR training software as well as flight controls and related services. Find out more.
SafetyScan Pro provides streamlined access to thousands of aviation accident reports. Tailored for your safety management efforts. Book your demo today
AeroInside Blog
Popular aircraft
Airbus A320Boeing 737-800
Boeing 737-800 MAX
Popular airlines
American AirlinesUnited
Delta
Air Canada
Lufthansa
British Airways